Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Atlas Flashing Replacement: The Woodland Hills Owner’s Guide
Atlas flashing replacement in Woodland Hills typically runs $285 – $640 installed, depending on which flashing point has failed and how much of the surrounding shingle or underlayment needs to come up. We stock Atlas-compatible flashing profiles on our trucks and can usually complete the swap the same day we arrive. Most homeowners discover a flashing failure the hard way: a water stain on the ceiling after the first hard rain, or a roof leak that only shows up when wind drives rain sideways against a chimney or wall junction.
Flashing is the metal shield that seals the seams where your roof meets something vertical: a chimney, a skylight, a vent pipe, a wall. When it fails on an Atlas roof, water gets under the shingles and travels sideways before it ever shows up inside your house. By the time you see the stain, the flashing has been failing for months.
Which Atlas Models This Applies To
Atlas flashing isn’t a one-size-fits-all part, which is exactly where DIY orders go sideways. The flashing profile has to match the shingle’s exposure and the specific penetration you’re sealing. We work with Atlas roofing systems across the board: Pinnacle, StormMaster, GlassMaster, and the Chalet shingle line all use industry-standard step flashing and counter-flashing dimensions, but wall-step flashing and chimney saddles need to be cut and bent to match the roof’s pitch and the shingle’s reveal.
Here’s the compatibility gotcha we see constantly in Woodland Hills: older Atlas installations from the 1990s and early 2000s often used 4-inch step flashing with a 5-inch head lap. Newer Atlas Pinnacle and StormMaster installs call for 5-inch step flashing with a 4-inch head lap. If you order the old 4-inch profile and the roofer doesn’t check the existing reveal, the new flashing sits too short and leaks within a season. We measure on-site before any order goes in.
On the OEM-versus-aftermarket question: Atlas doesn’t manufacture flashing. Like every major shingle brand (GAF, CertainTeed, and Owens Corning included), Atlas specifies galvanized steel or aluminum flashing profiles that third-party manufacturers produce to industry standards. For most Woodland Hills homes, a quality 26-gauge galvanized steel flashing with a G-60 coating matches or exceeds what the original builder used. We stock both steel and aluminum on the truck so we match the existing metal and avoid galvanic corrosion at the contact points.
Styles & brands we work with
Signs Your Atlas Flashing Replacement Is Failing
- Water stains on ceilings or walls near a chimney, skylight, or dormer. This is the classic flashing failure signature. Water enters at the flashing seam, travels along the roof deck, and pools at the lowest point of the ceiling, which is often several feet away from the actual leak.
- Visible corrosion or rust lines on exposed flashing. In Woodland Hills, the marine layer and morning fog from the coast accelerate rust on galvanized flashing faster than most owners expect. Once you see orange-brown streaking down the flashing face, the metal is actively thinning and will develop pinholes within one to two rain seasons.
- Lifted or separated step flashing along roof-to-wall junctions. Asphalt shingles expand and contract with our 40-degree temperature swings between summer afternoons and coastal nights. That movement slowly works step flashing loose from the mortar joint it’s tucked into.
- Granule loss concentrated around flashings. If you’re seeing dark patches or bare fiberglass around chimney bases and vent pipes, water is running under the shingle edge and stripping the protective granules. That’s a flashing seal problem, not a shingle problem.
- Daylight visible from the attic around vents or chimneys. Get into the attic on a bright day. If you can see light coming through gaps around the vent pipe or chimney, water can absolutely get through the same gaps.
Replacement Cost & What’s Included
Here’s the honest price picture for Atlas flashing replacement in Woodland Hills, as of 2026:
| Scope | Typical Installed Price |
|---|---|
| Single vent pipe boot replacement (rubber + flashing) | $285 – $420 |
| Chimney step flashing + counter-flashing (one side) | $340 – $520 |
| Chimney saddle/cricket and full re-flash | $520 – $640 |
| Step flashing replacement along a wall junction (per 10 linear feet) | $300 – $480 |
| Skylight re-flash (standard curb-mounted unit) | $420 – $610 |
The range depends on how much of the surrounding Atlas shingle we have to lift, whether the underlayment underneath is still sound, and whether the existing flashing was bedded in mortar that needs to be ground out and repointed. You get a written price before any work starts, and the number on that page is the number on the invoice. Every flashing replacement carries our 365-Day Done Right Promise: if it fails within a year, we come back and fix it at no charge. No negotiation, no fine print.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Flashing replacement sits in an awkward middle ground: it looks approachable, but doing it correctly requires lifting shingles without breaking them, matching the existing metal gauge and profile, and knowing how to seal the junction so it survives Woodland Hills’ summer heat and winter rain. Vent pipe boots are the one exception, a single-piece replacement you can sometimes handle on a single-story roof if you’re comfortable with basic tools and the roof pitch is walkable. For chimneys, wall junctions, and skylights, DIY attempts fail most often at the corner cuts and counter-flashing bends. If the new flashing doesn’t overlap correctly, you’ll be paying for an interior repair on top of the redo.
If you’d rather not spend a Saturday on a ladder only to find out the flashing profile doesn’t match, call us at (650) 456-5615. We’ll send a background-checked technician with a live arrival time you can track, and you’ll get before-and-after photos plus a digital invoice by text. The estimate is free either way.
FAQs
In Woodland Hills’ specific climate, galvanized steel flashing typically lasts 15 to 25 years before pinholes or seam separation develop. The marine layer fog we get from the coast accelerates corrosion on exposed metal, and the repeated heat cycling from summer sun causes expansion and contraction that eventually cracks old sealant at the flash-to-shingle joint. Aluminum flashing lasts longer in coastal air but isn’t compatible with every roof junction. Call (650) 456-5615 and we’ll evaluate what’s on your roof and what’s actually failing before recommending a replacement material.
Sometimes, yes. If the flashing metal is still structurally sound and the failure is limited to dried-out sealant or a separated lap joint, we can re-seal or re-seat the existing flashing and buy you several more seasons. But if there’s visible rust-through, cracked corner bends, or the flashing has pulled loose from the mortar joint entirely, patching it just delays the inevitable leak. We’ll tell you which camp you’re in after a roof inspection, and the written estimate will show exactly what we recommend and why. Call (650) 456-5615 for an assessment.
Most single-point flashing replacements, like a vent boot or a single chimney side, take two to three hours from setup to cleanup. A full chimney re-flash with a saddle or cricket is a half-day job, and a long wall-junction re-flash can run five to six hours depending on the length of the junction and the condition of the shingles we’re lifting. We’ll give you a realistic time window on the written estimate, and you’ll get a live trackable arrival link the morning of the job. Call (650) 456-5615 to schedule.
We stock standard flashing profiles and materials on our trucks: 26-gauge galvanized steel step flashing in both 4-inch and 5-inch profiles, aluminum coil for custom counter-flashing, vent pipe boots in the most common diameters, and chimney saddle materials. If your home needs an unusual profile or a custom copper piece, we source it locally in the San Fernando Valley within one to two business days. Call (650) 456-5615 with your Atlas shingle details and we’ll confirm what’s on hand before we schedule the visit.
Call for a Free Flashing Estimate in Woodland Hills
Every promise we make goes in writing, because a handshake doesn’t keep the rain out. If you’ve got a stain on the ceiling, rust on the flashing, or you just want a professional set of eyes on your Atlas roof before the next rain season, call Crestview Roofing Co Woodland Hills at (650) 456-5615. The estimate is free, the price is written before we start, and the repair is covered for 365 days. We’re an independent Woodland Hills roofing contractor, not affiliated with Atlas, so we call it straight either way.
Written by Dylan Pace, Owner, Crestview Roofing Co Woodland Hills at Crestview Roofing Co Woodland Hills, serving Woodland Hills and nearby areas.