Boral Ridge Vent Installation Nationwide

Boral Ridge Vent Installation: The Woodland Hills Owner’s Guide

Boral ridge vent installation in Woodland Hills typically runs $475 to $1,100 for a standard single-family home, depending on linear footage and whether we’re replacing just the vent material or also repairing the sheathing underneath. We stock Boral-compatible ridge vent components on our trucks, so most jobs are done in a single visit. You’ve probably landed here because you noticed something off: water staining near the peak of your ceiling, shingle granules in your gutter directly below the ridge, or maybe you were up on a ladder cleaning gutters and saw a cracked or warped section of vent. That’s how most Woodland Hills homeowners first discover the problem. The good news is this is a fix we do regularly, and we give you a written price before any work starts.

Call (650) 456-5615

Which Boral Models This Applies To

Boral’s ridge vent line in Southern California breaks down into two main families: the Slimline series (lower profile, often paired with Boral concrete and steel tile profiles) and the Ventilated Ridge series built for Boral’s flat and low-profile tile systems. Knowing which one you have matters because the vent widths and the matching closure strips are not interchangeable. The Slimline runs about 9 inches wide and nestles tighter to the tile profile, while the Ventilated Ridge sits closer to 11 inches and needs a wider gap cut in the sheathing.

If you’re not sure which Boral vent you have, the fastest way to identify it is to look at the end cap or the underside of any exposed section. Boral stamps the series name right into the molded plastic or metal. No stamp? Measure the overall width and whether the vent sits flush with the tile or stands proud of it. Then call us and describe what you’re seeing. Dylan Pace and the crew have matched enough Boral profiles across Woodland Hills that we can usually tell you over the phone what you’re working with.

One thing to know up front: we are an independent roofing company. We’re not affiliated with Boral, and we don’t pretend to be. What we do is stock Boral-compatible components and install them the way Boral’s installation specs call for, so your roof’s ventilation and tile profile stay true to the original design.

Signs Your Boral Ridge Vent Installation Is Failing

• Water staining along the ceiling peak inside your home. A cracked or separated vent section lets rain drive in sideways during the Santa Ana winds we get in Woodland Hills. The stain usually shows up as a faint brown line that follows the ridge.
• Granules from your tiles collecting in gutters below the ridge. When the vent shifts or its closure strip degrades, the tiles closest to the peak start rubbing against each other and against the vent edges. The result is accelerated granule loss in a very specific band.
• Visible cracking, warping, or sun-bleaching on the vent itself. The San Fernando Valley sun is relentless. Ten to fifteen years of UV exposure makes plastic vents brittle. If you can see visible cracks or a chalky, faded surface, the material is on borrowed time.
• Attic feels hotter than it used to in summer. A collapsed or blocked vent stops the passive air flow that pulls heat out of your attic. Your AC works harder, and your cooling bill climbs. That’s often the first sign owners notice before any water appears.
• Birds, rodents, or bees entering near the ridge. Gaps from a broken vent are an open invitation. We’ve pulled more than one bird’s nest out of a Woodland Hills ridge line, usually right where the vent had pulled away from the closure strip.

Replacement Cost & What’s Included

For Woodland Hills homes with standard single-story or two-story rooflines, most Boral ridge vent replacements run between $475 and $1,100 installed. That includes removing the old vent, inspecting the sheathing underneath, replacing the closure strip, setting the new Boral-compatible vent, and sealing all fasteners. If we find rotted sheathing below, that adds roughly $85 to $140 per 4×8 sheet, and we’ll show you a photo of the damage before we touch it.

Every job gets a written price before any work begins. The number on the page is the number on the invoice. We don’t pad the quote and we don’t come back with a change order unless there’s something we couldn’t have known until the old vent was off. And because we follow The Relay Standard, you’ll get before-and-after photos and a digital invoice by text before we leave the driveway.

Our workmanship on ridge vent replacement is covered by the 365-Day Done Right Promise: any covered repair that fails within 365 days is corrected at no charge, including a free second visit. Every promise we make goes in writing, because a handshake doesn’t keep the rain out.

DIY or Call Us?

Here’s the honest answer: a ridge vent replacement means working at the highest point of your roof, often on a steep pitch, usually while handling tiles that don’t appreciate being stepped on. This is not a Saturday-morning project. One wrong step and you’re looking at a broken tile, a damaged vent section, or a fall. We’ve fixed enough DIY attempts in Woodland Hills to say plainly: this one is worth paying for.

What you can safely check yourself: walk the perimeter of your home and look up at the ridge line from the ground. Use binoculars if you have them. Look for gaps, cracks, or sections of vent that aren’t sitting flush. Check your attic on a dry day for any light coming through at the peak. That’s useful information to share with us when you call. Leave the ladder work to a crew that does this weekly.

If you think your Boral ridge vent is failing, call (650) 456-5615. We’ll give you a straight answer and a free estimate.

FAQs